ROBOTC.net forums
http://robotc.net/forums/

RobotC for EV3
http://robotc.net/forums/viewtopic.php?f=1&t=7698
Page 5 of 6

Author:  auggie246 [ Wed Apr 16, 2014 4:27 am ]
Post subject:  Re: RobotC for EV3

Is there any beta version that can be use by public. I really do not like the EV3 software

Author:  mightor [ Wed Apr 16, 2014 6:57 am ]
Post subject:  Re: RobotC for EV3

Soon! We're working on get the last bits sorted out before we can release a beta build. Keep in mind that some features will not be supported straight away :)

= Xander

Author:  tfriez [ Wed Apr 16, 2014 1:23 pm ]
Post subject:  Re: RobotC for EV3

Our plan for our first BETA release. Our first BETA version will be released in next few days (Friday this week, or Monday next week)

BETA version will support the following:
* Generic Motor Support (unregulated movements)
* PID Motor Support (regulated movements)
* Encoder Support (reading encoders + moving to encoder targets)
* Full EV3 Sensor Support
* Limited NXT Device Support (basic sensors + motors)
* Normal ROBOTC features - Debugger, Multitasking, Variables, Debug Stream, etc.

Features not in the 1st BETA
* I2C / TETRIX support
* LCD support (drawing/printing text)
* EV3 specific features (LEDs, buttons, sounds)
* Bluetooth/Wifi specific commands
* Daisy Chaining EV3's together and using daisy chained motors/sensors
* Other stuff I'm probably not thinking of.

BETA Users will be able to either update the 16MB on-brick memory with a new kernel + ROBOTC firmware, or use a SD memory card to run the ROBOTC kernel + VM on.

Author:  auggie246 [ Sun Apr 20, 2014 9:39 pm ]
Post subject:  Re: RobotC for EV3

Really hope to get the beta today (monday) I only need the basic features you mentioned anyway

Author:  mightor [ Mon Apr 21, 2014 2:14 am ]
Post subject:  Re: RobotC for EV3

We now have the firmware loading working well, and that was one of the major blockers for us. I think an installer will need to be created and tested for this and then we're good to go for release, I believe :)

Tim will be able to say more about that particular process than I can.

= Xander

Author:  auggie246 [ Mon Apr 21, 2014 2:29 am ]
Post subject:  Re: RobotC for EV3

Cause I am actually waiting for the program to demonstrate the sequence to my teachers (they are kinda impatient)
Yeap i wrote the program already, (I hate GUI programming)

Author:  MHTS [ Mon Apr 21, 2014 2:57 am ]
Post subject:  Re: RobotC for EV3

I am also anxious for the beta release. I have already ported the GyroBoy LabView program to RobotC and can't wait to debug it.

Author:  auggie246 [ Mon Apr 21, 2014 9:33 pm ]
Post subject:  Re: RobotC for EV3

still waiting :( Tim

Author:  tfriez [ Mon Apr 21, 2014 9:54 pm ]
Post subject:  Re: RobotC for EV3

We'll have the website up tomorrow for download - the primary issue we're running into is a final delay-load DLL issue with the NI provided casper library (VM/clean machine testing of the installer)

Author:  auggie246 [ Mon Apr 21, 2014 10:25 pm ]
Post subject:  Re: RobotC for EV3

I really hope so :( my teacher is asking my all day long, is ur robot ready yet!!!!

Author:  tfriez [ Tue Apr 22, 2014 4:15 pm ]
Post subject:  Re: RobotC for EV3

It's posted :)

viewtopic.php?f=1&t=8577

Author:  mightor [ Wed Apr 23, 2014 12:20 am ]
Post subject:  Re: RobotC for EV3

Auggie, now that you have ROBOTC for EV3, is your bot done yet?

How about now?

= Xander

Author:  balu2012 [ Mon May 05, 2014 1:14 pm ]
Post subject:  Re: RobotC for EV3

when it will be possible to work with tetrix?

Author:  louis uz [ Sat Jun 07, 2014 5:50 am ]
Post subject:  Re: RobotC for EV3

I am new here. I want to be a robotic engineer/ technician. I'm good at maths but not so good at physics. i'm also good at electronics and I know a little about programming. what should I do?

Author:  Sirius [ Thu Jul 31, 2014 2:09 am ]
Post subject:  Re: RobotC for EV3

Just checking how the next build is going. Do we have a sneak preview of the features to be added and when it is going to be ready. How close to a commercial product is it expected to be.

Page 5 of 6 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/