View unanswered posts | View active topics It is currently Tue Jun 18, 2013 10:34 pm

 Page 1 of 1 [ 2 posts ]
 Print view Previous topic | Next topic
Full Servo Range
Author Message
Rookie

Joined: Wed Oct 24, 2012 9:08 pm
Posts: 1
Full Servo Range
When I program the servos to move from the range of -127--+127 the servos only move about 165-170 degrees, as appose to the 180-degrees they're suppose to, and when you unplug the servos and turn off the lock it shows that the servos are capable of moving the 180-degree, which makes me think it's a programming thing. Is there a way to program the servos to move the full 180-degrees?
-SuperSammy!!!

Wed Oct 24, 2012 11:28 pm

Joined: Thu May 24, 2012 12:15 pm
Posts: 399
Re: Full Servo Range
Unfortunately, ROBOTC is only able to send a command to the Cortex telling it what the desired position should be; the Cortex then converts that into the pulse train that is used to actually control and move the servo. In some cases, the physical range of the servo (in this case, 180 degrees) falls outside of the standard pulse waves (1.0 ms to 2.0 ms, with 1.5 ms being dead center). This varies from servo to servo and is unfortunately difficult to compensate for before hand.

In this case, since the Cortex (and not ROBOTC) controls the pulse wave output, any range values outside of the standard will not be reachable. The best thing I can recommend in this case is to use physical gearing ratios to access the full 180 degrees of movement (at the cost of servo accuracy).

12/10/12: To clarify; the VEX servos have a listed range of 100 degrees of movement. This is an electrical limit; when ROBOTC sends the Cortex a value of -127, it will move the servo to -50 degrees, and when ROBOTC sends it a value of 127, it will move the servo to +50 degrees. This limit cannot be overcome on the servo itself. The only way to change the range of movement from a servo is to gear the output of the servo appropriately. The servo will still have the electronic limit on how far it can move in one direction or the other, but the output's gearing will help to compensate for this. Hope this helps clarify, and I apologize for any confusion this may have caused.

_________________
Check out our Blog! And our Facebook page!
Need help? Take a look at our Wiki and our Forums.

I just met you,
And this is crazy,
But here's my code now,
So fix it, maybe?
~ Carly Rae Jepsen parody

Thu Oct 25, 2012 9:47 am
Display posts from previous:  Sort by
 Page 1 of 1 [ 2 posts ]

#### Who is online

Users browsing this forum: No registered users and 2 guests

 You cannot post new topics in this forumYou cannot reply to topics in this forumYou cannot edit your posts in this forumYou cannot delete your posts in this forumYou cannot post attachments in this forum

Search for:
 Jump to:  Select a forum ------------------ ROBOTC Applications    ROBOTC for LEGO MINDSTORMS       Third-party sensors    ROBOTC for CORTEX & PIC    ROBOTC for Arduino    Robot Virtual Worlds    Multi-Robot Communications    Issues and Bugs Competitions & Partners    2013 Robotics Summer Of Learning       VEX Toss Up Programming Challenge       FTC Ring It Up! Programming Challenge    Competitions using VEX - BEST, TSA, VEX, and RoboFest!    FTC Programming    RoboCup Junior and Other ROBOT Competitions    Robotics Merit Badge Robotics Discussions    General Discussions    Project Discussions International Forums    Spanish Forums       ROBOTC for MINDSTORMS       ROBOTC for VEX    French Forums       ROBOTC pour Mindstorms       ROBOTC pour IFI VEX    Japanese Forums （日本語のフォーラム） Off-Topic ROBOTC Forum & ROBOTC.net Suggestions/Feedback    ROBOTC Forums Suggestions/Comments    ROBOTC.net Suggestions/Comments       NXT Programming: Tips for Beginning with ROBOTC       VEX Programming: Tips for Beginning with ROBOTC